Drywall Tape & Bed Philadelphia Pennsylvania
You may be surprised at how effective the application of tape and bed is. The use of tape and bed for drywall repair jobs can be an economical way to fix any small tears or cracks in your drywall. Tape and bed not only make repairs easier, but they also prevent future damage. Read on to learn more about the benefits of taping and bed for your drywall needs.
A common problem in drywall jobs is the presence of gaps between the drywall surface and the edges of the wall. This often occurs because the drywall was installed at an angle, resulting in an uneven foundation. It may have even been created by shims that were not properly installed or removed. Tape and bed can be used to fill up these gaps, providing you with a level, smooth surface that will not be easily damaged. It will also provide a firm support to the walls where it is placed, which will help eliminate the need for sagging if you plan to add wallpaper to the area. |
|
215-201-4957
Many times taping and bed is used to repair tears in drywall panels. This is because the tape can be applied to the whole panel, while adding seam allowances to each side to help fix the rip. There are several different techniques that can be used to patch the torn seams, depending on how much is damaged. The simplest technique involves placing the tape over the area and sewing around the edges, creating a waterproof layer that will stop moisture from leaking out of the affected area. If there are no tears in the panel, then this technique can be used to simply patch the area.
A slightly more difficult method involves taping sheetrock & drywall panels while waiting for the adhesive to dry. Start by lining up one side of the panel with the corner beads, then unfold the panel so that the next row is lined up. Using a drywall knife, carefully scrape off the paper towel that was used to line the seams. These methods are often combined in order to create an even application that will seal the corners without over stretching. Once the tape is dry, you can scrape off the excess tape and gently brush in the drywall mixture to give your wall a clean finish.
When the joint compound is ready, you will need a small hand saw to cut strips of tape that match the thickness of the paper tape. Depending on the amount of damage you see, you may want to apply a mask to prevent further damage to the wall. Use the saw's blade to cut through the paper tape at various angles until the desired length is achieved. Apply the tape to the area in such a way as to hide the joint compound if necessary. Once the tape is completely installed, you can use the joint compound as usual.
Some materials can be difficult to work with if you do not have a tape and binder combination. If this is the case, a small amount of drywall joint compound can be applied to the area using a taping knife and then a drywall knife. If the compound does not come out the same color as the paper tape, simply blend in with the wallpaper. When finished, simply cut off the excess compound.
To complete one wall, begin by lining up the four-inch end of the tape along the outside perimeter of the frame and then carefully push the tape into place. The tape should first be secured at the corners before working around the inside corner. Be sure to overlap the tape by one inch from the corners. Once the tape is secured, push the mud into place and then slowly push the tape into the two-inch inside corner bead.
When finishing the project, it is important to always stagger the pieces of tape. This will ensure that you do not have any sharp ends that can potentially damage your drywall. Be careful when using the compound to prevent any scratches or smudges on the drywall surface. The tape can be kept neatly tucked under the drywall knife block with a drywall knife or drywall anchors. By following these simple steps, a tape and bed will add an instant finish to any unfinished interior walls.
A slightly more difficult method involves taping sheetrock & drywall panels while waiting for the adhesive to dry. Start by lining up one side of the panel with the corner beads, then unfold the panel so that the next row is lined up. Using a drywall knife, carefully scrape off the paper towel that was used to line the seams. These methods are often combined in order to create an even application that will seal the corners without over stretching. Once the tape is dry, you can scrape off the excess tape and gently brush in the drywall mixture to give your wall a clean finish.
When the joint compound is ready, you will need a small hand saw to cut strips of tape that match the thickness of the paper tape. Depending on the amount of damage you see, you may want to apply a mask to prevent further damage to the wall. Use the saw's blade to cut through the paper tape at various angles until the desired length is achieved. Apply the tape to the area in such a way as to hide the joint compound if necessary. Once the tape is completely installed, you can use the joint compound as usual.
Some materials can be difficult to work with if you do not have a tape and binder combination. If this is the case, a small amount of drywall joint compound can be applied to the area using a taping knife and then a drywall knife. If the compound does not come out the same color as the paper tape, simply blend in with the wallpaper. When finished, simply cut off the excess compound.
To complete one wall, begin by lining up the four-inch end of the tape along the outside perimeter of the frame and then carefully push the tape into place. The tape should first be secured at the corners before working around the inside corner. Be sure to overlap the tape by one inch from the corners. Once the tape is secured, push the mud into place and then slowly push the tape into the two-inch inside corner bead.
When finishing the project, it is important to always stagger the pieces of tape. This will ensure that you do not have any sharp ends that can potentially damage your drywall. Be careful when using the compound to prevent any scratches or smudges on the drywall surface. The tape can be kept neatly tucked under the drywall knife block with a drywall knife or drywall anchors. By following these simple steps, a tape and bed will add an instant finish to any unfinished interior walls.